How to Tie the Poppin' Flats Shrimp

How to Tie the Poppin' Flats Shrimp fly tying video
SaltwaterTied by MaxApril 21, 202013 min video
New fly every Tuesday on YouTube.Subscribe on YouTube

Join Max as he ties the Poppin' Flats Shrimp, an easy-casting saltwater shrimp for baby tarpon, snook and bonefish around the mangroves and flats.

Poppin' Flats Shrimp recipe

We matched the colors and sizes used in the video. Change any option, uncheck what you already have, then add it all at once.

$0.000 items selected

Get the new fly every Tuesday

One email a week: the newest Fly Tying Tuesday video, the full recipe and the materials to tie it. 9 years and 500+ videos strong.

You're in. Watch your inbox next Tuesday.
No spam. Unsubscribe anytime.

More Saltwater to tie

See all

Rather fish it than tie it? Shop ready-tied Saltwater →

Read the video transcript

So in the vise I've got the X-Series all-purpose hook from Umpqua. It's one of our newer hooks; this is the XS410. Now, I really like this hook. I've been using it on all our streamers as well; it's just a great all-around hook. It's a size 2 in the vise, and we've got some UTC Ultra Thread in the 140 in tan.

Start my thread wraps just behind the eye here and work my way down to the bend. Snip out my excess, walk my thread out, work just around the bend a little bit, and then I'm going to take a piece of my Crystal Flash. You can use pearl like he's black you love. That's just the antennae of the shrimp. Get in there a couple of lengths of the body and snip it out.

I'm going to take a knot there, string my Silly Legs, and I'll have that on my thread. Tie that down right on top. Got those tied in. I've got my crab eyes, shrimp eyes, and we're going to tie those in just at the bend there, same deal.

I kind of want these angled down a little bit. Once you've got one eye tied in there, tie in my other eye and make sure that stays on the side of the shank here. Snip out my excess mono, and I'll clean up the wraps on the bottom here to make everything uniform. So you've got that in there. Once again, I'll bend my eyes outward and flare them a little bit.

Trim our rubber legs down just a little bit. I'm going to take some UV Ice Dub in the tan, and I pull apart my fibers and make sure that I get the long ones in there. I'll bring my thread right to where the bend starts and tie in a patch. Make two securing wraps, pull it over, double it up, hold them all back and tie that down in there, right back to where my eyes are tied in. Pluck out some loose ones.

Now prep some of my foam. I'm cutting a half-inch strip, fairly long, for the body piece, and then another small diamond piece for the back of my shrimp here. Tie in the diamond so it makes it easier to tie down to the shank. Spy red tip, work my way back, even good, crank down on the rest of the foam, that bulk out of there. Let's go that side end.

I'll take my longer strip here and tie it in at the diamond, going back. Put that all the way back to the smaller piece I tied in; I kind of blended them up against each other. Crank the rest of that foam down. Now I'm going to take my Tarantula Brush. You can use the Shrimp Dub Brush, you can just transfer, but I like this one because of the legs.

Tie that in right back at my foam here, and bring my thread about halfway up the shank. I'm going to make wraps going forward with my brush, pretty sparse; I'm not really overlapping, so they're kind of up against one another. Then I'll capture my brush, make a couple of wraps and run in behind, and pull them back with a couple of wraps. Then I'm going to part the top of the brush with a brush and fold my piece of foam over it. It makes a nice little buggy, crustacean-looking hard shell on top.

Capture my foam, make sure it stays on top of the fly there, and make a couple of tightening wraps. Then I'll bring my thread in front of the foam. This is where it can get a little tricky; you don't want to crowd the eye of the fly. I want to make two even, segmented wraps like I just did, so it's going to be real light with my brush. Capture it and snug that down, a couple of wraps.

Fold it back over, put more wraps in front, and then take a couple more wraps with my brush. Sneak it behind the eye here, pull everything back and trim out my brush. Then one more wrap over the top with my foam, kind of a loose one, and then I can pull it and snug it down. Then I'm going to fold everything back and work it just behind the eye.

Your spacing might take a little practice; I try to get it as close as I can to the eye without crowding it up. Do my whip finish, and I'll clean up the excess and just snip my thread out. So I've got two fairly even ones in the front and a big one in the back, and then I'm like a nice straight line, just so it's overlapping. It helps push some water. I'm going to go in and clean up the rubber legs around the eye here.

So I'll take my dubbing brush and rough up the legs here on the bottom. Make sure they're all sticking out; I want to pull them straight down. Then I've got my five-inch pair of scissors here, and I'm just going to make an angled trim going back so I'm not crowding the hook point. Pull everything back so my eyes are splayed out, and there you have it, the Poppin' Flats Shrimp.